Menu
Your Cart

W1209 Digital Temperature Controller Thermostat Module

W1209 Digital Temperature Controller Thermostat Module
W1209 Digital Temperature Controller Thermostat Module
W1209 Digital Temperature Controller Thermostat Module
-17 %
W1209 Digital Temperature Controller Thermostat Module
W1209 Digital Temperature Controller Thermostat Module
W1209 Digital Temperature Controller Thermostat Module
W1209 Digital Temperature Controller Thermostat Module
Settings Chart:-Long press the “SET” button to activate the menu.Code Description Range Default ValueP0 Heat C/H CP1 Backlash Set 0.1-15 2P2 Upper Limit 110 110P3 Lower Limit -50 -50P4 Correction -7.0 ~ 7.0 0P5 Delay Start Time 0-10 mins 0P6 High-Te..

Write a review

Note: HTML is not translated!
Bad Good
  • Stock: In Stock
  • Reward Points: 50
  • Model: INO-000113
  • Weight: 50.00g
Products Sold 0
1,000.00DA
1,200.00DA
Price in reward points: 1200

 

 

 

 

Settings Chart:-


Long press the “SET” button to activate the menu.

Code Description Range Default Value

P0 Heat C/H C

P1 Backlash Set 0.1-15 2

P2 Upper Limit 110 110

P3 Lower Limit -50 -50

P4 Correction -7.0 ~ 7.0 0

P5 Delay Start Time 0-10 mins 0

P6 High-Temperature Alarm 0-110 OFF

Long pressing +- will reset all values to their default

Working:-


Current temperature will be displayed on the module in degree Celsius by default. When switched to a different mode, inactivity for approximately 5 seconds would lead to restoring the value of the module to the default temperature display.


Setting Modes:-


Trigger Temperature:Press “SET” button on the module and current temperature will be displayed on the screen. Using “+” and “-“ button, one can set the temperature in 0.1 degrees (Celsius) increments. No activity for 2 seconds will result in setting and storing the trigger temperature and then the screen will display the current temperature.


Parameters Setting:-


Pressing the “SET” button for a minimum of 5 seconds will lead to the setting of the parameter present in the module. The seven segment display will start with the display of first parameter “P0”. Pressing ‘ + ’ or ‘ – ‘ buttons will help to go to parameters (P0-P6). Pressing “SET” button midst the parameters will let you change the value for that parameter. After setting the required parameter, press set button to exit that option. If no button is pressed for 5 seconds the thermostat will exit the parameter option and will return back to the default temperature.


Heating Parameter P0: P0 has two settings, C and H. The default setting C can be used to connect to an air-conditioner as the relay energizes when the temperature is reached. Setting H leads to de-energizing the relay when the required temperature is detected. It can be used to control any heating device.


Hysteresis Parameter P1: This parameter sets the range of change in temperature that must occur before relay will change state.


Parameter P2 (Upper Limit Temperature): P2 limits the maximum trigger temperature that can be set. It acts as a safety feature that stops the user to set an extremely high trigger temperature.


Parameter P3 (Lower Limit Temperature): P3 limits the minimum trigger temperature that can be set. It also acts as a safety feature that stops the user to set a low triggering temperature.


Offset Correction Parameter P4: Changes can be made if there is a difference between the displayed temperature and actual temperature reading with this parameter.


Delay Parameter P5: Delay in the switching of the relay when the trigger temperature has reached, can be set by the help of delay parameter P5. It can be set in one-minute increments up to a maximum of 10 minutes.


Alarm Parameter P6: This parameter causes the relay to switch off when the temperature reaches its settings. The display will show ‘ — ‘ to indicate an alarm condition. The relay will not re-energize until the temperature falls below this value.


Application :


To measure and display temperature

To Turn any application ON/OFF based on temperature reading . (Both AC and DC)

Example Project :- A.Fire alarm system . B. Auto cut off Electric Water Heater

Package Includes : 


1 x W1209 Temperature control switch with Temperature sensor and display

Notification Module
This is the sticky Notification module. You can use it for any sticky messages such as cookie notices or special promotions, etc.